View BD63847EFV_4989520.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1/4
STRUCTURE PRODUCT SERIES TYPE FUNCTION
Silicon monolithic integrated circuits Bipolar stepping motor driver
BD63847EFV
PWM constant current controllable two H bridge driver Built-in translator circuit for CLK-IN control Full, Half, Eighth, and Sixteenth step modes Mix decay control
Absolute maximum ratings(Ta=25C) Item Supply voltage
Ratings Unit -0.3+36.0 V 1 W 1.45 Power dissipation Pd 4.702 W Input voltage for control pin VIN -0.3+7.0 V RNF voltage VRNF 0.7 V 3 Output current IOUT 2.0 A/phase Output current(peak)4 IOUTPEAK 2.53 A/phase Operating temperature range Topr -25+85 C Storage temperature range Tstg -55+150 C Junction temperature Tjmax +150 C 1 70mmx70mmx1.6mm glass epoxy board. Derating in done at 11.6mW/C for operating above Ta=25C. 2 4-layer recommended board. Derating in done at 37.6mW/C for operating above Ta=25C. 3 Do not, however exceed Pd, ASO and Tjmax=150C. 4 Pulse width tw1ms, duty 20%.
Symbol VCC1,2
Operating conditions (Ta=-25+85C) Item Symbol Supply voltage VCC1,2 Input voltage for control pin VIN
Min. 19 0
Typ. 24 -
Max. 28 5.5
Unit V V
This product isn't designed for protection against radioactive rays.
REV. A
2/4 Electrical characteristics (Unless otherwise specified, Ta=25C, VCC1,2=24V) Item Symbol Min. Limit Typ. Max. 2.5 5.0 0.8 100 Unit Conditions
Whole Circuit current at standby ICCST 1.0 Circuit current ICC 2.5 Control input (CLK, CW_CCW, MODE0, MODE1, ENABLE, PS) H level input voltage VINH 2.0 L level input voltage VINL H level input current IINH 35 50 L level input current IINL -10 0 Output (OUT1A, OUT1B, OUT2A, OUT2B) Output ON resistance Output leak current Current control RNFXS input current RNFX input current VREF input current VREF input voltage range MTH input current MTH input voltage range Minimum on time (Blank time) Comparator threshold 1 Comparator threshold 2 Comparator threshold 3 RON ILEAK IRNFS IRNF IVREF VREF IMTH VMTH tONMIN VCTH1 VCTH2 VCTH3 -2.0 -40 -2.0 0 -2.0 0 0.3 0.570 0.403 0.196 0.85 -0.1 -20 -0.1 -0.1 0.8 0.600 0.424 0.230
mA mA V V A A
PS=L PS=H, VREF=3V
VIN=5V VIN=0V IOUT=1.5A, Sum of upper and lower
1.10 10 3.0 3.5 1.5 0.630 0.445 0.264
A A A A V A V s V V V
RNFXS=0V RNFX=0V VREF=0V MTH=0V C=1000pF, R=39k VREF=3V, 100% VREF=3V, 70.71% VREF=3V, 38.27%
REV. A
3/4 Package outline Product No.
BD63847EFV
Lot No.
HTSSOP-B28 (Unit:mm)
Block diagram
Pin No. / Pin name Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Pin name GND OUT1B RNF1 RNF1S OUT1A NC VCC1 NC GND CR NC MTH VREF PS Pin No. 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Pin name CLK CW_CCW TEST MODE0 MODE1 ENABLE NC VCC2 NC OUT2A RNF2S RNF2 OUT2B NC
CLK 15 CW_CCW 16 MODE0 18 MODE1 19 ENABLE 20 Translator RESET
Regulator
9 GND 14 PS
UVLO OVLO TSD
VREF 13

4bit DAC
OCP
7 VCC1
RNF1S 4

5 OUT1A 2 OUT1B
Control logic
RNF2S 25

3 RNF1
Blank time PWM control CR 10 OSC Mix decay control
Predriver
22 VCC2 24 OUT2A 27 OUT2B 26 RNF2
NC : Non Connection
MTH 12 TEST 17
1 GND
REV. A
4/4 Operation Notes (1) Absolute maximum ratings An excess in the absolute maximum ratings, such as supply voltage, temperature range of operating conditions, etc., can break down the devices, thus making impossible to identify breaking mode, such as a short circuit or an open circuit. If any over rated values will expect to exceed the absolute maximum ratings, consider adding circuit protection devices, such as fuses. (2) Power supply lines As return of current regenerated by back EMF of motor happens, take steps such as putting capacitor between power supply and GND as an electric pathway for the regenerated current. Be sure that there is no problem with each property such as emptied capacity at lower temperature regarding electrolytic capacitor to decide capacity value. If the connected power supply does not have sufficient current absorption capacity, regenerative current will cause the voltage on the power supply line to rise, which combined with the product and its peripheral circuitry may exceed the absolute maximum ratings. It is recommended to implement a physical safety measure such as the insertion of a voltage clamp diode between the power supply and GND pins. (3) GND potential The potential of GND pin must be minimum potential in all operating conditions. (4) Metal on the backside (Define the side where product markings are printed as front) The metal on the backside is shorted with the backside of IC chip therefore it should be connected to GND. Be aware that there is a possibility of malfunction or destruction if it is shorted with any potential other than GND. (5) Thermal design Use a thermal design that allows for a sufficient margin in light of the power dissipation (Pd) in actual operating conditions. This IC exposes the metal on the backside of package. Note that this part is assumed to use after providing heat dissipation treatment to improve heat dissipation efficiency. Try to occupy as wide as possible with heat dissipation pattern not only on the board surface but also the backside. (6) Operation in strong electromagnetic field Use caution when using the IC in the presence of a strong electromagnetic field as doing so may cause the IC to malfunction. (7) ASO When using the IC, set the output transistor so that it does not exceed absolute maximum ratings or ASO. (8) Thermal shutdown circuit The IC has a built-in thermal shutdown circuit (TSD circuit). If the chip temperature becomes Tjmax=150C, and higher, coil output to the motor will be open. The TSD circuit is designed only to shut the IC off to prevent runaway thermal operation. It is not designed to protect or indemnify peripheral equipment. Do not use the TSD function to protect peripheral equipment. (9) Ground wiring pattern When using both large current and small signal GND patterns, it is recommended to isolate the two ground patterns, placing a single ground point at the ground potential of application so that the pattern wiring resistance and voltage variations caused by large currents do not cause variations in the small signal ground voltage. Be careful not to change the GND wiring pattern of any external components, either. (10) TEST pin Be sure to connect TEST pin to GND.
REV. A
Notice
Notes
No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuelcontroller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law.
Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us.
ROHM Customer Support System
http://www.rohm.com/contact/
www.rohm.com (c) 2010 ROHM Co., Ltd. All rights reserved.
R1010A

▲Up To Search▲

Price & Availability of BD63847EFV

	To Download BD63847EFV Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .